ICF-1170I Series

Introduction
The ICF-1170I Series CAN-to-fiber converters are used to convert CAN signals from copper to optical fiber. The converters come with 2 kV optical isolation for the CAN bus system and dual power inputs with alarm contact relay to ensure that your CAN bus system will remain online.

 

Fiber Test Mode
Fiber Test Mode can be used to test the fiber cable between two ICF-1170I units, and it provides a simple way to determine if the fiber cable is transmitting data correctly. When in Fiber Test Mode, the fiber transceiver (Tx) will continuously send out a data signal and the Fiber Tx LED will light up. On the other side of the connection, when the ICF-1170I fiber transceiver (Rx) receives the data signal from the Tx side, the Fiber Rx LED will light up.

ICF-1170I Series

Category:

Features and Benefits

  • Transmits data up to 2 km over optical fiber
  • Converts CAN signals to fiber and fiber to CAN signals
  • Baudrate up to 1 Mbps
  • Dual power inputs for redundancy
  • DIP switch for 120 ohm terminal resistance
  • DIP switch for fiber test mode
  • LEDs for Fiber Tx, Fiber Rx, Power 1, Power 2
  • Wide-temperature model available for -40 to 85°C environments
  • Fully compatible with the ISO 11898 standard

Certifications

Download Datasheet

Description

Introduction
The ICF-1170I Series CAN-to-fiber converters are used to convert CAN signals from copper to optical fiber. The converters come with 2 kV optical isolation for the CAN bus system and dual power inputs with alarm contact relay to ensure that your CAN bus system will remain online.

 

Fiber Test Mode
Fiber Test Mode can be used to test the fiber cable between two ICF-1170I units, and it provides a simple way to determine if the fiber cable is transmitting data correctly. When in Fiber Test Mode, the fiber transceiver (Tx) will continuously send out a data signal and the Fiber Tx LED will light up. On the other side of the connection, when the ICF-1170I fiber transceiver (Rx) receives the data signal from the Tx side, the Fiber Rx LED will light up.

Specification

Isolation 2 kV (built-in)
No. of Ports 1
Signals CAN_L, CAN_H, CAN Signal GND
Terminator N/A, 120 ohms (by DIP)

Input Current 221 mA @ 12 to 48 VDC
Power Consumption 221 mA @ 12 to 48 VDC
Input Voltage 12 to 48 VDC
No. of Power Inputs 2
Overload Current Protection Supported
Power Connector Terminal block (for DC models)

Housing Metal
IP Rating IP30
Dimensions 30.3 x 70 x 115 mm (1.19 x 2.76 x 4.53 in)
Weight 178 g (0.39 lb)
Installation DIN-rail mounting

Operating Temperature ICF-1170I-M-ST: 0 to 60°C (32 to 140°F)
ICF-1170I-M-ST-T: -40 to 85°C (-40 to 185°F)
Storage Temperature (package included) -40 to 85°C (-40 to 185°F)
Ambient Relative Humidity 5 to 95% (non-condensing)

EMC EN 55032/24
EMI CISPR 32, FCC Part 15B Class A
EMS IEC 61000-4-2 ESD: Contact: 8 kV; Air: 15 kV
IEC 61000-4-3 RS: 80 MHz to 1 GHz: 3 V/m
IEC 61000-4-4 EFT: Power: 4 kV; Signal: 2 kV
IEC 61000-4-5 Surge: Power: 1 kV
IEC 61000-4-6 CS: 150 kHz to 80 MHz: 3 V/m; Signal: 3 V/m
IEC 61000-4-8 PFMF
Environmental Testing IEC 60068-2-1
IEC 60068-2-2
IEC 60068-2-3
Safety EN 62368-1
Vibration IEC 60068-2-6

Time 792,085 hrs
Standards Telcordia (Bellcore), GB

Warranty Period 5 years
Details See www.moxa.com/warranty

Models